江苏铆钉机,浙江铆钉机,上海铆钉机

Brief introduction to automatic rivet machine wear reasons and operating procedures!

Fully automatic riveting machine is mainly used for hot riveting of metal structure, such as automobile beam riveting, bridge riveting, mining car riveting, etc. It can also be used for other work occasions that need to produce impact energy, such as shovel cutting metal, casting finishing, eradicating burr and welding scar. It is mainly used for hot riveting of metal structure, such as automobile girder, bridge, mining car, etc. It can also be used in other operations where impact energy is needed, such as shovel cutting metal, casting, burr eradication and welding scar. The following small make up for you to talk about automatic rivet machine wear reasons and operating procedures!

A, automatic rivet machine wear reasons

1. The belt is off track. The belt deviation is affected by the wear of the drum and the abnormal operation of the idlers. There is a lot of pressure on the roller at the high point of the belt offset. Long working rolls just wear and thin until they crack. Roller wear is more in the belt section before unloading.

2. The ash belt of the rivet machine belt is sticky with dust. Blade wear, not close to the belt surface, ash viscosity increase, high water content. The surface of the belt is provided with a slag pipe belt conveyor.

3. High water content of ash and slag of riveting machine. The filter element and drain pipe of filter residue water filter are blocked, the gate drain pipe is blocked, and the water filter component is not washed in time after slag discharge, resulting in excessive water carried by ash residue.

4, buffer slag box ash is straight. The ash of the slag machine is not dehydrated for a certain period of time and is directly conveyed to the dewatering tank by the tubular belt conveyor, which will constitute more ash and water, while the tubular belt conveyor will increase the empty load time and increase the wear of the roller.

5, riveting machine bearing quality. Some roller working face is clean, because bearing quality problems will also cause insensitive or stuck changes, and then wear.

6, riveting machine bearing quality. Some roller face cleaning, because bearing quality problems will also cause insensitive or stuck, and then wear.

7, the sealing performance of riveting machine is poor. Slag is collected into the idler bearing, forming blockage or changing sensitivity and forming wear. The slurry slag has worn on the idler. Sometimes the slurry ash from the slag machine is simply attached to tape and dropped onto the bracket and roll shaft at each end of the roller. On the one hand, the roll body wears away; on the other hand, it agglomerates. 8. Wear ash with large particle size on the roller. Sometimes, the larger ash from the slag machine sticks to the tape, and the hard, sharp material wears away quickly on the roller body.

Two, automatic riveting machine operating rules

1. When running the automatic rivet machine, the operator should stand firmly with legs apart.

2, test automatic riveting machine, should be on the wooden pier, not on the cement floor and steel plate test.

3, automatic rivet machine to check the gallbladder, it is necessary to close the door after the wind. It is strictly prohibited to lift the riveting gun, place it horizontally to people and pry inward.

4, the automatic riveting machine of the bristle application wire tied to the handle, temporarily need not be placed in the local collision is not easy.

5, automatic riveting machine needs to determine the top of the top, to open the riveting, such as the workpiece is too big, can not see the top staff, should echo each other.

6, automatic rivet machine before operation, should wear protective glasses, tighten the cuffs, buckle the collar. The head should be under the rivet.

7, it is necessary to wait for the head contact rivet, can open the wind riveting, start to the wind is not suitable for too large.

8, the nail burning core temperature is low, not riveting. When you need to nail out, you need to go through the top nail promise to gently knock.

9. When starting the automatic riveting machine, the electrical switch, oil pipe joint and other parts should pay attention to extrusion, and the movement should be sensitive. The lifting arm should have a strong end magnetic head. Keep an eye on people and objects as you move.

Riveting machine work to pay attention to what?

A rivet machine is a mechanical device that rivets objects together. Rivet machine is mainly assembled by rotation and pressure, rivet machine is mainly used in rivets (hollow rivets, hollow rivets, solid rivets, etc.) riveting occasions, common pneumatic, hydraulic and electric, single head and double head specifications. The common type is mainly automatic riveting machine (mainly for the riveting of semi-hollow rivets, can automatically feed, riveting efficiency is high!) And rotary riveting machine (rotary riveting machine is divided into pneumatic rotary riveting machine and hydraulic rotary riveting machine, mainly used for solid rivets, or large hollow rivets).

1. The rear stopper adjustment usually has electric quick adjustment and manual fine tuning.

2, bending notch selection. For example, bending 3mm plate, need to choose about 35 notch.

3, if it is an automatic rivet machine, set the trip of the rivet machine, the application must pay attention to the scheduling trip, must be detected before bending. Check the die of rivet machine, adjust the stroke according to customer's requirement.

4, step on the foot switch preliminary bending. The riveting machine can be loose and terminated anytime and anywhere in the process of processing. Step on the cloud to continue processing. But this is only semi-automatic riveting machine, like automatic riveting machine can not control.

5. Start the rivet machine, turn over the switch on the operation panel, and see the rivet head in rotation on behalf of its working.